The correct ways to use automatic start and stop are: step on the brake, wading in the water without turning on and stopping, turning on the brake and stepping on the accelerator, etc. Step on the brake. The correct way to start, stop and stop automatically is to step on the brake, stop firmly, then hang the idle gear, and pull the handbrake.
Automatic start-stop accuracyThe exact usage method is: the automatic start-stop system can only work normally when using an automatic transmission car. When the driver steps on the brake, most of the engines will automatically turn off within 1 to 2 seconds.
The correct way to use automatic start-stop is: when the brake holding system is disabled: when the gearshift lever is placed in D gear, step on the brake pedal and stop the vehicle. ( Engine stop) release the brake pedal and start the engine. When the brake maintenance system is enabled: When the gearshift lever is in D gear, step on the brake pedal and stop the vehicle.
1. The brake light fuse burns out, and the engine cannot start normally. At this time, when the engine start/stop button is in the ACC state, press the engine start/stop button for 10 seconds to start the engine.
2. The correct way to use the automatic start and stop of the engine: step on the brake, stop firmly and then hang the idle gear, and pull the handbrake.
3. When the start-stop system is turned off, fuel cannot be added. The owner will not get out of the car when refueling. Directly open the fuel tank cover for the staff to refuel. At this time, the vehicle only turns off the engine for a short start and stop, and starts at any time. It will be very dangerous to add fuel at this time. Please remember that the vehicle must be completely turned off before refueling.
4. The correct way to use automatic start and stop is: when the brake maintenance system is disabled: when the gearshift lever is placed in D gear, step on the brake pedal and stop the vehicle. ( Engine stop) release the brake pedal and start the engine. When the brake maintenance system is enabled: When the gearshift lever is in D gear, step on the brake pedal and stop the vehicle.
5. The correct use of the automatic start-stop function of the car is as follows: when starting, stop and turning off, quickly turn to P gear, you can release the brake, the engine will not start, continue to stay quietly, when the D gear is turned off, pull up the handbrake and release the brake will not continue to turn off. In order to start faster at any time, even if you hang into the N gear engine It will start.
The correct use of automatic start and stop are: stepping on the brake, wading in the water without turning on and stopping, turning on the brake and stepping on the accelerator, etc. Step on the brake. The correct way to start, stop and stop automatically is to step on the brake, stop firmly, then hang the idle gear, and pull the handbrake.
The brake light fuse is broken, and the engine cannot start normally. At this time, the start/stop button on the engineIn the ACC state, press the engine start/stop button for 10 seconds to start the engine.
The correct way to use automatic start-stop is: when the brake holding system is disabled: when the gearshift lever is placed in D gear, step on the brake pedal and stop the vehicle. ( Engine stop) release the brake pedal and start the engine. When the brake maintenance system is enabled: When the gearshift lever is in D gear, step on the brake pedal and stop the vehicle.
The correct use of the automatic start-stop function of the car is as follows: quickly turn to P gear when starting and stopping, you can release the brake, the engine will not start, continue to stay quietly, when the D gear is turned off, pull up the handbrake and release the brake will not continue to turn off. In order to start faster at any time, even if it is hung in N gear, the engine will start Move.
Through the productDuring the waterway section, remember that the start-stop system must be turned off. In case you need to stop while driving and the engine is turned off, the exhaust pressure will suddenly decrease. Water is easy to flow back into the engine from the exhaust pipe, causing the engine to fail to start.
1. The correct way to use automatic start and stop is: when the brake holding system is disabled: when the gearshift lever is placed in D gear, step on the brake pedal and stop the vehicle. ( Engine stop) release the brake pedal and start the engine. When the brake maintenance system is enabled: When the gearshift lever is in D gear, step on the brake pedal and stop the vehicle.
2. The starting steps of the automatic transmission are as follows: ignition. One-click start-up models need to be started with one click twice. The first press is the self-examination of the vehicle, and the second press needs to step on the brake to ignite. Atten your seat belt. Step on the brake. Hang the D gear. Release the handbrake.
3. Steering wheel lock When the engine start and stop button is closed, the steering wheel is locked to prevent theft; when the door is opened or the smart key is removed from the smart key lock cylinder, the steering wheel will be locked automatically.Under normal circumstances, when the engine start-stop button is in ACC mode, the steering wheel will be automatically unlocked.
okx.com login-APP, download it now, new users will receive a novice gift pack.
The correct ways to use automatic start and stop are: step on the brake, wading in the water without turning on and stopping, turning on the brake and stepping on the accelerator, etc. Step on the brake. The correct way to start, stop and stop automatically is to step on the brake, stop firmly, then hang the idle gear, and pull the handbrake.
Automatic start-stop accuracyThe exact usage method is: the automatic start-stop system can only work normally when using an automatic transmission car. When the driver steps on the brake, most of the engines will automatically turn off within 1 to 2 seconds.
The correct way to use automatic start-stop is: when the brake holding system is disabled: when the gearshift lever is placed in D gear, step on the brake pedal and stop the vehicle. ( Engine stop) release the brake pedal and start the engine. When the brake maintenance system is enabled: When the gearshift lever is in D gear, step on the brake pedal and stop the vehicle.
1. The brake light fuse burns out, and the engine cannot start normally. At this time, when the engine start/stop button is in the ACC state, press the engine start/stop button for 10 seconds to start the engine.
2. The correct way to use the automatic start and stop of the engine: step on the brake, stop firmly and then hang the idle gear, and pull the handbrake.
3. When the start-stop system is turned off, fuel cannot be added. The owner will not get out of the car when refueling. Directly open the fuel tank cover for the staff to refuel. At this time, the vehicle only turns off the engine for a short start and stop, and starts at any time. It will be very dangerous to add fuel at this time. Please remember that the vehicle must be completely turned off before refueling.
4. The correct way to use automatic start and stop is: when the brake maintenance system is disabled: when the gearshift lever is placed in D gear, step on the brake pedal and stop the vehicle. ( Engine stop) release the brake pedal and start the engine. When the brake maintenance system is enabled: When the gearshift lever is in D gear, step on the brake pedal and stop the vehicle.
5. The correct use of the automatic start-stop function of the car is as follows: when starting, stop and turning off, quickly turn to P gear, you can release the brake, the engine will not start, continue to stay quietly, when the D gear is turned off, pull up the handbrake and release the brake will not continue to turn off. In order to start faster at any time, even if you hang into the N gear engine It will start.
The correct use of automatic start and stop are: stepping on the brake, wading in the water without turning on and stopping, turning on the brake and stepping on the accelerator, etc. Step on the brake. The correct way to start, stop and stop automatically is to step on the brake, stop firmly, then hang the idle gear, and pull the handbrake.
The brake light fuse is broken, and the engine cannot start normally. At this time, the start/stop button on the engineIn the ACC state, press the engine start/stop button for 10 seconds to start the engine.
The correct way to use automatic start-stop is: when the brake holding system is disabled: when the gearshift lever is placed in D gear, step on the brake pedal and stop the vehicle. ( Engine stop) release the brake pedal and start the engine. When the brake maintenance system is enabled: When the gearshift lever is in D gear, step on the brake pedal and stop the vehicle.
The correct use of the automatic start-stop function of the car is as follows: quickly turn to P gear when starting and stopping, you can release the brake, the engine will not start, continue to stay quietly, when the D gear is turned off, pull up the handbrake and release the brake will not continue to turn off. In order to start faster at any time, even if it is hung in N gear, the engine will start Move.
Through the productDuring the waterway section, remember that the start-stop system must be turned off. In case you need to stop while driving and the engine is turned off, the exhaust pressure will suddenly decrease. Water is easy to flow back into the engine from the exhaust pipe, causing the engine to fail to start.
1. The correct way to use automatic start and stop is: when the brake holding system is disabled: when the gearshift lever is placed in D gear, step on the brake pedal and stop the vehicle. ( Engine stop) release the brake pedal and start the engine. When the brake maintenance system is enabled: When the gearshift lever is in D gear, step on the brake pedal and stop the vehicle.
2. The starting steps of the automatic transmission are as follows: ignition. One-click start-up models need to be started with one click twice. The first press is the self-examination of the vehicle, and the second press needs to step on the brake to ignite. Atten your seat belt. Step on the brake. Hang the D gear. Release the handbrake.
3. Steering wheel lock When the engine start and stop button is closed, the steering wheel is locked to prevent theft; when the door is opened or the smart key is removed from the smart key lock cylinder, the steering wheel will be locked automatically.Under normal circumstances, when the engine start-stop button is in ACC mode, the steering wheel will be automatically unlocked.
846.33MB
Check618.88MB
Check494.77MB
Check562.53MB
Check283.98MB
Check934.65MB
Check199.88MB
Check724.71MB
Check159.62MB
Check335.58MB
Check454.47MB
Check851.27MB
Check796.75MB
Check715.29MB
Check735.64MB
Check261.55MB
Check945.79MB
Check647.78MB
Check483.94MB
Check928.71MB
Check972.42MB
Check712.38MB
Check271.57MB
Check668.95MB
Check288.68MB
Check727.91MB
Check949.46MB
Check461.55MB
Check598.33MB
Check577.19MB
Check471.49MB
Check955.96MB
Check388.85MB
Check444.23MB
Check547.39MB
Check548.98MB
CheckScan to install
okx.com login to discover more
Netizen comments More
700 塞井焚舍网
2025-02-02 20:28 recommend
904 万夫莫当网
2025-02-02 20:12 recommend
1835 断子绝孙网
2025-02-02 18:55 recommend
1586 自食其言网
2025-02-02 18:40 recommend
2153 顺天应时网
2025-02-02 18:05 recommend